Mitsubishi Lancer Owners Manual
Changing the function settings (when the ignition switch is “ON”)Instruments and controls / Multi-information display / Changing the function settings (when the ignition switch is “ON”)
1. Stop the vehicle in a safe place.
Firmly apply the parking brake and put the gearshift lever into the “N” (Neutral) position (M/T), the selector lever into the “P” (PARK) position (CVT) or the gearshift lever into the “P” (PARK) position (Twin Clutch SST).
2. Lightly press the multi-information meter switch a few times to switch the information screen to the function setting screen. Refer to “Information display (when the ignition switch is “ON”)”.
► For safety, stop the vehicle before operating.
While driving, even if you operate the multi- information meter switch, the function
setting screen is not displayed.
3. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.
Note
► To return the menu screen to the function setting screen, press and hold the
multi-information meter switch for about 2 seconds or more.
► If no operations are made within about 15 seconds of the menu screen being displayed,
the display returns to the function setting screen.
4. Select the item to change on the menu screen and change to the desired setting. Refer to the following items for further details on the operation methods.
Changing the reset mode for average fuel consumption and average speed
The mode conditions for the average fuel consumption and average speed display can be switched between “Auto reset” and “Manual reset”.
1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select “AVG (average fuel consumption and average speed setting)”.
3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from A or 1 (Auto reset mode) → M, 2 or P (Manual reset mode) → A or 1 (Auto reset mode).
The setting is changed to the selected mode condition.
Manual reset mode
► When the average fuel consumption and average speed are being displayed, if
you hold down the multi-information meter switch, the average fuel consumption and
average speed displayed at that time are reset.
► When the ignition switch is switched from “ACC” or “LOCK” to “ON”, the mode setting
is automatically switched from manual to auto.
Switching to auto occurs automatically. If switching to manual mode is done, however, the data from the last reset is displayed.
Auto reset mode
► When the average fuel consumption and average speed are being displayed, if
you hold down the multi-information meter switch, the average fuel consumption and
average speed displayed at that time are reset.
► If the ignition switch is at “ACC” or “LOCK” for about 4 hours or longer, the
average fuel consumption display and average speed display are automatically reset.
Note
► The memory of the auto reset mode or manual reset mode for the average speed
display is erased if the battery is disconnected.
► The initial (default) setting is “Auto reset mode”.
Changing the fuel consumption display unit
The display unit for fuel consumption can be switched.
The distance, speed, and amount units are also switched to match the selected fuel consumption unit.
1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select “AVG UNIT (fuel consumption display setting)”.
3. Press and hold the multi-information meter switch for about 2 seconds or more to display “AVG UNIT” (fuel consumption display unit setting).
4. Lightly press the multi-information meter switch to switch in sequence from km/L → L/100 km → mpg (US) → mpg (UK) → RETURN → km/L.
5. Press and hold the multi-information meter switch for about 2 seconds or more to change the setting to the selected unit.
Note
► The display units for the driving range, the average fuel consumption, the
average speed and the momentary fuel consumption are switched, but the units for
the indicating needle (speedometer), the odometer and the tripmeter will remain
unchanged.
► The memory of the unit setting is erased if the battery is disconnected, and it
returns automatically to L/100 km.
The distance and speed units are also switched in the following combinations to match the selected fuel consumption unit.
Changing the temperature unit
The display unit for temperature can be switched.
1. Press and hold the multi-information meter switch for about 2 seconds or more
to switch from the setting mode screen to the menu screen. Refer to “Changing the
function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select
(temperature unit setting).
3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from °C → °F → °C.
The setting is changed to the selected temperature unit.
Note
► If the battery is disconnected, the unit setting is erased from memory and is automatically set to °C.
Changing the display language
The language of the multi-information display can be switched.
1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select “LANGUAGE” (language setting).
3. Press and hold the multi-information meter switch for about 2 seconds or more
to display “LANGUAGE” (language setting).
4. Lightly press the multi-information meter switch to select the desired language.
5. If you hold down the multi-information meter switch for about 2 seconds or more,
the setting is changed to the selected language.
Note
► The memory of the language setting is erased if the battery is disconnected,
and it returns automatically to ENGLISH or RUSSIAN.
► If “---” is selected in the language setting, a warning message is not displayed
when there is a warning display or interrupt display.
Changing the language cooperative control
The language used in MITSUBISHI Multi-Communication System (MMCS) (if so equipped) or the Bluetooth® 2.0 interface (if so equipped) can be changed automatically to the same language as that shown in the multi-information display.
1. Press and hold the multi-information meter switch for about 2 seconds or more
to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select
(language cooperative control).
3. Press and hold the multi-information meter switch to switch in sequence from A or 1 (language cooperation enabled) → M, 2 or P (language cooperation disabled) → A or 1 (language cooperation enabled).
The setting is changed to the selected condition.
Note
► The memory of the language cooperative control is erased if the battery is
disconnected, and it returns automatically to A or 1 (language cooperation enabled).
► The language display modified with the language setting can be switched in the
following manner.
• When A or 1 (language cooperation enabled) has been selected with the language
cooperative control, the language for MITSUBISHI Multi-Communication System (MMCS)
(if so equipped) or the Bluetooth® 2.0 interface (if so equipped) is automatically
changed to the language selected for the multi-information display.
• When M, 2 or P (language cooperation disabled) has been selected with the language
cooperative control, the language for MITSUBISHI Multi-Communication System (MMCS)
(if so equipped) or the Bluetooth® 2.0 interface (if so equipped) is not automatically
changed to the language selected for the multi-information display.
Operation sound setting
You can turn off the operation sounds of the multiinformation meter switch and daytime dipper button.
1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select
(operation sound setting).
3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from ON (operation sound on) → OFF (operation sound off) → ON (operation sound on).
The setting is changed to the selected condition.
Note
► The memory of the operation sound setting is erased if the battery is disconnected,
and it returns automatically to ON (operation sound on).
► The operation sound setting only deactivates the operation sound of the multi-information
meter switch and daytime dipper button. The warning display and other sounds cannot
be deactivated.
Changing the time until “REST REMINDER” is displayed
The time until the display appears can be changed.
1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select “ALARM” (rest time setting).
3. Press and hold the multi-information meter switch for about 2 seconds or more to display “ALARM” (rest time setting).
4. Lightly press the multi-information meter switch to select the time until
the display.
5. Press and hold the multi-information meter switch for about 2 seconds or more,
the setting is changed to the selected time.
Note
► If the battery is disconnected, the unit setting is erased from memory and
is automatically set to OFF.
► The drive time is reset when the ignition switch is turned off.
Changing the turn-signal sound
It is possible to change the turn-signal sound.
1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select
(changing the turn-signal sound).
3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from 1 (turn-signal sound 1) → 2 (turn-signal sound 2) → 1 (turn-signal sound 1).
The setting changes to the selected turn-signal sound.
Changing the momentary fuel consumption display (Type 2)
It is possible to change the bar graph setting of the momentary fuel consumption display.
1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select
(changing the momentary fuel
3. Press and hold the multi-information meter switch for about 2 seconds or more to switch in sequence from ON (with the green bar graph) → OFF (without the green bar graph) → ON (with the green bar graph).
The setting changes to the selected bar graph setting.
Returning to the factory settings
All of the function settings can be returned to their factory settings.
1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select “RESET” (returning
to the factory settings).
3. When you press and hold the multi-information meter switch for about 5 seconds or more, the buzzer sounds and all of the function settings are returned to the factory settings.
Note
► The factory settings are as follows.
• Average fuel consumption and average speed reset mode: A (Auto reset)
• Fuel consumption display unit: L/100 km
• Temperature unit: °C (Celsius)
• Display language: ENGLISH or RUSSIAN
• Cooperative language setting: A
• Operation sounds: ON (Operation sounds on)
• “REST REMINDER” display: OFF
• Turn-signal sound: Turn-signal sound 1
• Momentary fuel consumption with the green bar graph (Type 2): ON
